Product properties

PRECOAT 367-200 Color with Sand is available in Red, Moss Green, Grass Green, Blue or other colours upon request. .
3.1 Technical data
BASIC DATA(for mixed product at 20 °C)
Mass density: approx.1,37 g/cm³
Solids content: approx.71 % by volume
Touch after dry: ½-1 hour
Overcoating interval: Min.2 hours
Theoretical spreading rate:0,450 kg/m²(Depending on surface permeability and porosity) per each coat.
 

Mixing Location

Choose a location to mix materials that is close to the court entrance and will not require the mixed materials to be carried over patios, walkways etc. A vinyl drop sheet is recommended to protect lawns when mixing and spillage that may occur when transferring the material from the mixing drum to pails.
Mix PRECOAT 367-200 and water together until materials are blended to a smooth, slightly thick but free flowing homogenous consistency. A wooden pad-dle can be used, however, a ¾" electric drill and mixing shaft is available from most tool rental stores and is certainly much easier to use.
Clean Up: Wash tools with water. If material has dried, use kerosene.
 

Surface Preparation

New asphalt must cure for 21 days prior to application of color coatings. Repair of pavement surface defects, cracks, depressions and/or base coat (if necessary) must be completed prior to color coating applications. Pavement surface must be cleaned entirely of dust, dirt, mildew (if any) debris and all loose materials in-cluding vegetation. All repairs must be flush and smooth to adjoining surfaces.
Using the long handled sqeegee apply surface coating by walking beside the windrow of wet material pulling the squeegee in even straight lines and on a slight angle to allow the material to flow in front of, and off the rubber squeegee blade. Although you will be using a 60 cm wide squeegee, you will only be flowing new material to the suface in a 15 cm to 20 cm width with each pass across the court. The rest of the squeegee blade is wiping off excess material from your previous passes. You cannot take off too much material with the squeegee. The thickness of the sand in the material will always allow the right coating thickness to remain on the court.
A slight downward pressure should be applied to the squeegee blade to prevent leaving any puddles while applying a uniform coat from one side of the court to the other. Each return pass (pulling of material) should be parallel to the last.
When applying surface coatings during periods of very hot weather, apply coat-ings during the coolest part of the day, usually in the early morning. Do not ap-ply if surface temperature is 60 degrees C or above. When you encounter hot weather which the surface temperature will exceed 60C, it is best to apply one coat in the early morning before the temperature rises and then wait until the next morning to apply the next coat.
When doing a two color application, the playing box is coated first. Both coats of color will be applied before the outbound area is started.
In order to complete the application of two coats of color over the playing box surface, it is necessary to identify the four corners of an existing playing box, and/or layout the perimeter lines of the playing box on a new court, which you do not have the benefit of having existing lines to work from. The existing outer perimeter lines of the playing box (or the new chalk-line box that you will create for a new court) will be completely covered when coating the playing box.
Very Important:
The playing box surface is now finished except for striping the playing lines. You will now be changing over to the 2nd color. Do not walk on the finished surface while working with the 2nd color. Be sure to instruct everyone working with you to carry the 2nd color around the finished playing box. Any paint on shoes while working with the alternate color could be tracked unto the finished playing box.
 

Coverage Rates/Material Requirements & Ordering

Historic yield calculations are based on undiluted 75 kg pails of PRECOAT 367-200 Color with Sand within the following limits: 175 m2 per 75 kg pail for one coat. (2 coats recommended)
Coverage rates may vary depending on the surface porosity, ambient tempera-ture and application technique.
 

Mixing Ratios (for 1 drum)

ТекстPrecoat 367-200 …... 150 kg
Water.................... 10-30 kg
Important:The amount of water required will vary according to ambient tem-perature. Higher temperatures may require greater water dilution to a maximum of 30% of the undiluted PRECOAT 367-200 Color with Sand.
 

Storage

The product is stored in sealed containers placed at indoor dry warehousing premises within the temperature range from 14° C to 60° C. Shelf life (warranty) is 12 months from the production date in cool and dry place.
 

Packaging

25 kg in tin cans or 75 kg in p.e.drum.